RIDGID RSM3300 Bedienerhandbuch PDF herunterladen (Seite 6)

TRANSFORMER FEATURES

• Whenpluggedinto120VAC,thetransformerautomatically

provides power to the battery charging circuitry.

• Thetransformercanbeleftconnectedtothewalloutlet

indefinitely.

• Thetransformerisdesignedforthesystemonly,DONOT

use for any other purpose.

PUMP INSTALLATION

The 12 Volt Advanced Notiﬁcation System can be installed as

a back-up system with a separate dedicated discharge line

(Method 1), or tied into an existing sump pump line (Method 2).

1. Verify that the existing AC pump is in good working order. If

the AC pump is questionable, replace with the same HP

pump or increase the HP rating if you have experienced

ﬂooding or the pump is not keeping up with the inﬂow of

water.

2. Remove any silt or accumulated debris from the sump pit

and surrounding area.

3. Make sure that disconnecting the AC pump will not create a

flood in your basement. A pump should be available to

evacuate water in the event incoming water rates should

change.

METHOD 1 (PREFERRED) - See Figure 1

1. Locate the DC pump on a solid, level surface in the sump pit. Do

NOT place the pump on a loose or sandy surface. Small stones or

sand may damage the pump resulting in pump failure.

2. This pump has a 1-1/2 in. NPT discharge. If a 1-1/4 in.

discharge pipe is desired, an adapter (not included) will

be necessary. Smaller diameter piping will reduce pump

flow-rate and performance.

3. A check valve is required in the discharge line of both the

Main AC pump and the Back-Up DC Pump to prevent

recirculation of water into the sump pit. The system will not

function without two check valves.

4. Cut a 4 ft. section of 1-1/4 in. or 1-1/2 in. diameter rigid PVC

pipe. Cement 1-1/4 in. or 1-1/2 in. pipe to a threaded fitting.

Cement 1-1/4 in. or 1-1/2 in. pipe into pipe coupling. Attach

1-1/4 in. or 1-1/2 in. pipe section to the Back-Up DC Pump

discharge adapter.

5. Screw into pump discharge.

6. Place the pump with the 4 ft. section of PVC pipe on a solid,

level surface in the sump pit on an elevated surface.

7. Attach a rubber check valve (sold separately) to the top of

the discharge pipe. This will allow the pump or check valve

to be removed easily for servicing.

8. Check valve is recommended for effective operation of

system.

The remainder of the discharge pipe installation will vary

depending on individual circumstances. Using sound plumbing

practices, route the discharge pipe to an exterior wall by the

shortest path. Keep turns to a minimum because they reduce

ﬂow output of the pump. The pipe that exits the building structure

should be sloped downward so that water will not freeze in the

pipe.

When installing the separate discharge pipe, drill through

the outside wall with appropriate drilling equipment. Seal the

hole to prevent water from entering.

Installation of this unit MAY take several hours.

Before disabling your main pump, have a stand by

pump ready or an appropriate means of evacuating the sump.

Electric shock hazard. DISCONNECT power

before servicing. Apply a ﬁxed lock or tag to

prevent unexpected application of power.

DO NOT over tighten or cross-thread plastic

ﬁttings or check valves. USE rigid PVC or metal

pipe for permanent installation.

BACK-UP PUMP:

1. The pump will turn on when either the bottom or top float

rises.

2. The pump motor will keep running for 15 seconds after the

float drops.

3. An auto-test of the back-up pump will occur every 14 days

between the hours of 5pm-7pm. The controller will report

any known issues and record the date of the last auto-test

on the home screen.

4. The last known float activated back-up pump run date can

be found by scrolling through the main menu selections.

CHART 1 - STANDBY POWER PUMPING CAPACITY

40 A-Hr

75 A-Hr

*Hours of Protection During A Rain Event

If Your Sump Pump Runs...

12 Hours

23 Hours

1X Per

Min

1X Every

5 Min

1X Every

10 Min

Deep Cycle

Battery Size

53 Hours

100 Hours

92 Hours

172 Hours

*Assumes a typical 10 ft. rise on the discharge pipe, and

17 in. diameter sump pit. Results may vary.

PUMP INSTALLATION

1. Turn power to main pump off.

2. Pump must be installed using 1-1/4 in. or 1-1/2 in. rigid

PVC piping.

CONTROL BOX FEATURES

Check valves MUST be installed in the

discharge line of both the main AC pump and the

back-up DC pump. Failure to install the check valves MAY allow water to

recirculate into the sump pit. See Figures 1 and 2.

Ridge Tool Company

Model RSM3300 – Operating Instructions and Parts Manual

1 2 3 4 5 6 7 8 9 10 11 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

RIDGID RSM3300 Bedienerhandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein RIDGID RSM3300