RIDGID DP15501 Betreibershandbuch

Your new drill press has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When proper

10FEATURESKNOW YOUR DRILL PRESSSee Figure 2.Before attempting to use your drill press, familiarize yourself with all operating features and safety req

11The Drill Press is shipped complete in one box.n Remove the packing materials from around your drill press. n Separate all loose parts f

12LOOSE PARTS�1 Head Assembly... 1�2 Column Assembly...

13TOOLS NEEDEDADJUSTABLE WRENCHPHILLIPS SCREWDRIVERASSEMBLYWARNING:Do not connect to power supply until assembly is complete. Failure to comply c

14ASSEMBLYTO INSTALL THE TABLESee Figure 6.n Loosen table support lock and raise table support by turning table crank clockwise until sup

15TO INSTALL THE IDLER PULLEYSee Figure 8.n Locate the idler pulley and two belts.n Press the belt guard latch and lift belt guard.n Place a straighte

16ASSEMBLYTO INSTALL THE STORAGE TRAYSee Figure 10.n Locate the pre-assembled storage tray.n Completely remove the screw and hex nut from one side of

17ASSEMBLYTO INSTALL THE LIGHT BULBSee Figure 13.WARNING:Failure to unplug drill press could result in accidental starting causing possible

18®®OPERATIONWARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflic

19OPERATIONTO POSITION TABLE AND WORKPIECESee Figures 17 and 18.n Lock the table to the column in a position so that the tip of the drill is just a l

2TABLE OF CONTENTSn Introduction ...

20®®OPERATIONTO DRILL TO A SPECIFIC DEPTHSee Figure 19.To drill a blind hole (not all the way through) to a given depth, proceed as follow

21TO TILT TABLESee Figure 21.To use the table in a bevel (tilted) position:n Loosen the set screw under table bevel lock with hex key. Loose

22WARNING:Before performing any adjustment, make sure the drill press is unplugged from the power supply and the switch is in the OFF position. Failur

23®®ADJUSTMENTSTO CONVERT FROM RIGHT HAND OPERATION TO LEFT HAND OPERATIONSee Figures 23 - 27.The drill press is shipped from the factory with feed ha

24®®®ADJUSTMENTSn Remove the stop pin screw from the right side of the drill press and install in the left side of the drill press as shown

25ADJUSTMENTSWARNING:For your own safety turn switch OFF and remove plug from power source outlet before making any adjustments. To reduce t

26ADJUSTMENTSTO ADJUST THE BELT LATCH GUARDSee Figure 29.The button latch is adjusted at the factory to be self latching when the pulley guard lid is

27MAINTENANCEWARNING:When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product dama

28ACCESSORIESUse Only Accessories Designed For This Drill Press To Reduce the Risk of Serious Injury From Thrown Broken Parts Or Work

29TROUBLESHOOTINGDrill bit burns 1. Incorrect speed 1. Change speed. See “Adjustment” section. 2. Chips not coming out of hole 2. Retract drill bit

3GENERAL SAFETY RULESREAD ALL INSTRUCTIONSn KNOW YOUR POWER TOOL. Safe operation of this power tool requires that you read and understand thi

30NOTES

31This product is manufactured by One World Technologies, Inc., under a trademark license from RIDGID, Inc. All warranty communications should

32CUSTOMER SERVICE INFORMATIONFor parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information

4SPECIFIC SAFETY RULESn KEEP BITS CLEAN AND SHARP. Sharp bits minimize stalling. Dirty and dull bits may cause misalignment of the material and possi

5SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols wil

6SYMBOLSSAVE THESE INSTRUCTIONSThe operation of any tool can result in foreign objects being thrown into your eyes, which can result in severe eye dam

7ELECTRICALEXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the tool's plug.

8GLOSSARY OF TERMSBaseLarge rectangular plate that secures the drill press to a benchtop or other sturdy, level surface.ChipThe material extr

9FEATURESPRODUCT SPECIFICATIONSn Input....... 120V, 60 Hz, AC Only, 8 Amperesn Motor ............