RIDGID metal detector Betriebsanweisung Seite 107
- Seite / 144
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Operating Instructions
Learn Messages
The table below lists the messages that may appear during a Learn process and provides some
guidance.
Message Explanation
+Use ferrite+
This only applies when performing a ferrite tune
and indicates that either the
ferrite wand is not being passed through the machine or that there is
insufficient ferrite material in the wand. Check that the wand being used is the
one supplied with the machine.
+Head overload+
The message indicates that the gain cannot be reduced any further to stop the
head overloading. Possible reasons for this could be:
■
The sample pack being used contains a large contaminant.
■
A product not specified for use with the machine is being used.
■
The product packaging is highly conductive.
If in doubt, contact your local Loma Service Centre.
+Working dry+
This message indicates that the product has so little moisture that it produces
no product signal. The detector will automatically set the Working Mode to
DRY.
+Bad pack+
This message indicates that the product signal being received exceeds the
Max Threshold option value set in the Menus > Learn > Set Up menu.
This could be because the sample pack being used contains a contaminant or
the Max Threshold option value has been set too low.
Check that the sample packs being used are representative of production
packs. For example, if a frozen product is being learnt are the sample packs
still frozen?
If in doubt, contact your local Loma Service Centre.
+Adjusting+
The head is reducing the Gain and/or Frequency settings to account for the
product effect of the product.
+Head locked+ The head is using the Head Gain value entered in the Menus > Learn >
Setup menu rather than determining the value itself as the Head Gain option
has been set to LOCKED.
+Mode locked+ The head is using the Working Mode value entered in the Menus > Learn >
Setup menu rather than determining the value itself as the Working Mode
option has been set to LOCKED.
+Dry product+
The product has little or no product signal and therefore the wrong Working
Mode option may have been locked in the Menus > Learn > Setup menu.
+Learn
complete+
The Full Learn process has been completed successfully.
97
- Metal Detector User Guide 1
- Table of Contents 3
- Introduction 11
- About this Guide 12
- Organisation 13
- Document Change Control 14
- Document Key 14
- The Loma Group of Companies 16
- About Metal Detection 17
- How a Metal Detector Works 18
- Product Effect and Phasing 18
- Phasing 19
- Tracker Feature 20
- Metal Free Zone 20
- Detector Performance 20
- Types of Metal 22
- Test Frequency 23
- Product Test Samples 23
- Test Wands 24
- Testing Guidelines 24
- Test Records 24
- Learn Feature 25
- Safety First 27
- Safety Awareness 28
- EC Declaration of Conformity 28
- Safety Warnings 29
- Safety Labels 31
- Safety Guards 32
- Safety Measures 33
- Intended Use of the Machine 33
- Noise Levels 34
- End of Life Treatment 34
- Emergency Procedures 34
- Quality Assurance 35
- End User Licence Agreement 36
- Technical Specifications 37
- European Belt Conveyors 38
- Installation 39
- Warnings 40
- Receiving and Unpacking 40
- Moving the Detector Head 40
- Nuisance triggering 45
- Moving Metal 46
- Vibration 47
- Belting 47
- Electrical Interference 47
- Warnings 52
- Moving the Machine 53
- Clearance Requirements 54
- Connecting the Air Supply 54
- Checking Guards 57
- Site Considerations 58
- Radio Frequency Interference 59
- Metal Detector Search Heads 62
- Conveyor Belts 63
- Plastic Modular Belts 64
- Reject Devices 65
- Electrical Services Box 67
- Air Pressure Switch 67
- Optional Equipment 68
- Getting Started 71
- threshold 72
- display 72
- changes 72
- User Access 75
- Logging In and Out 76
- Starting and Stopping 77
- Stopping the Machine 78
- Emergency Stop 78
- Using the Metal Detector 79
- Handling Rejected Products 81
- Getting the Results 82
- Frequency Selection 82
- Operating Instructions 83
- Setting the Language 84
- Setting the Machine ID 84
- Setting Up the Search Head 86
- Setting Up the Conveyor 88
- Setting the VF Balance 92
- Setting the VF Drive 94
- Setting Up the User Options 95
- Setting Up Serial Links 96
- Reject Relay 101
- Reject Timing 101
- Adding a New Product 102
- Learning Products 104
- Full Learn 105
- Update Learn 106
- Learn Messages 107
- Learn Setup 108
- Learn Limits 110
- PQ span? 111
- Using Performance Validation 112
- Logs and Reports 117
- Errors Report 118
- Example Problems 119
- Faults Report 120
- Setup Report 123
- Contaminants Report 124
- Learn Report 125
- Status Report 126
- PV Test Report 126
- Batch Report 127
- Shift Report 128
- Contaminants Log 128
- Errors Log 129
- Faults Log 130
- Printing the Faults Report 131
- Clearing a Fault 131
- Clearing the Log 131
- Batch Log 132
- PVS Log 133
- Shift Log 134
- Maintenance 135
- Cleaning solutions 136
- Belt conveyor versions 136
- Conveyor Belt Maintenance 137
- Adjusting the Reject Devices 138
- Software Upgrades 138
Verwandte Produkte und Handbücher für Messen, Testen & Steuern RIDGID metal detector
(5 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern