Ridgid SP6490 Bedienungsanleitung

SAVE THIS MANUAL FOR FUTURE REFERENCE,1&+)/22502'(/'5,//35(66Part No. SP6490 Printed in China'323(5$725·60$18$/WARNING:

10Unpacking and Checking ContentsTools NeededUnpacking WARNING: For your own safety, never connect plug to power source outlet until all assembly

11List of Loose PartsItem Description Qty.A Head Asm. ...1B Table...

12Location and Function of Controls1. Belt Tension Handle...Turn handlecounterclockwise to apply tension tobelt, turn handle clockwise to releasebelt

13Assembly WARNING: To reduce the risk of injury from unexpected starting or electrical shock, never connect plug to outlet until all assembly ste

14Assembly (continued)Installing The Table1. Loosen support lock and raise tablesupport by turning table crank clock-wise until support is at a workin

15Installing the Head CAUTION: The head assembly weighs about 80 pounds. To reduce the risk of back injury get help to lift the head.1. Locate (2)

16Assembly (continued)Pulley Alignment and Speed AdjustmentChecking Pulley(s) Alignment WARNING: To reduce the risk of injury due to accidental st

17Tensioning Belt1. Apply tension to belt by turning belttension handle counterclockwise untilbelt deflects approximately 1/2 inch bythumb pressure at

18Assembly (continued)4. Unlock support lock and raise table soits about two (2) inches below tip ofchuck.5. Turn chuck sleeve clockwise and openjaws

19Installing Light Bulb WARNING: To reduce the risk ofelectrical shock, unplug the tool beforeinstalling light bulb.1. Remove the amber colored len

2Table of ContentsSection PageTable of Contents ... 2Safety Instructions For Drill Press ... 2Sa

20Assembly (continued)Converting From Right Hand Operation to Left Hand OperationThe drill press is shipped from the factorywith feed handles set-up f

217. Remove the 4mm socket head capscrew from the left side of the drillpress and install in the same positionon the right side of the drill press.Tig

22Assembly (continued) WARNING: For your own safety turn switch OFF (O) and remove plug from power source outlet before making any adjustments. To

23NOTE: For right hand operation (feedhandle on right side) turn spring counter-clockwise to the next notch and engagewith the 4mm cap screw.6. Finger

24Getting To Know Your Drill PressFeed SpringAdjustmentFeed Spring18 SpringCapLight “On-Off”Switch23 Table28 Drill “On-Off” Switch26 ChuckKey16 Depth

25Spindle Speed in R.P.M.1. Drill Speed Table...Drill Speed can bechanged by placing the belt in any oneof the stepped pulleys. The spindlespeed chart

26Getting To Know Your Drill Press (continued)25. Support Lock...Tightening locks tablesupport to column. Always have itlocked in place while operatin

27To lock switch in OFF (O) position, holdswitch IN with one hand and remove keywith other hand. WARNING: For your own safety, always push the swi

28Getting To Know Your Drill Press (continued)Locking Chuck at Desired Depth1. With the switch off, loosen the depthscale lock.2. Turn the feed handle

29Safety Instructions for Basic Drill Press OperationRead the following instructions for operating your drill press to get the best results and to min

3Before Using The Drill Press WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activi-ties contains

30Getting To Know Your Drill Press (continued)- Use the spindle speed recom-mended for the specific operationand workpiece material - check theinside

31Positioning Table and WorkpieceLock the table to the column in a positionso that the tip of the drill is just a littleabove the top of the workpiece

32Tilting TableTo use the table in a bevel (tilted) position,loosen the set screw under table bevellock with hex “L” wrench. Loosen bevellock bolt wit

33MaintenanceMaintenance WARNING: For your own safety, turn switch OFF (O) and remove plug from power source outlet before maintaining or lubricat

34Troubleshooting (continued)Trouble Probable Cause RemedyDrill bit burns 1. Incorrect speed2. Chips not coming out of hole3. Dull drill bit4. Feeding

35Repair PartsParts List for RIDGID 15" Drill PressModel No. DP15501Figure 1Always order by Part Number - Not by Key Number* Standard hardware it

36Repair PartsParts List for RIDGID 15" Drill PressModel No. DP15501Figure 2123456789101112131415161718192021222324262728293031323337394042434447

37Repair PartsParts List for RIDGID 15" Drill PressModel No. DP15501Figure 2Always order by Part Number -- Not by Key Number* Standard hardware i

38Repair PartsParts List for RIDGID 15" Drill PressModel No. DP15501Figure 3Always order by Part Number - Not by Key Number12345678910Key No.Part

39Repair PartsParts List for RDIGID 15" Drill PressModel No. DP15501Figure 4* Standard hardware item - may be purchased locally.12367810114522181

4Safety Instructions For Drill Press (continued)• Never Stand On Tool. Serious injury could occur if the tool tips or you accidentally hit the cutting

QUESTIONS OR COMMENTS?CALL 1-866-539-1710www.ridgid.comPlease have your Model Number and Serial Number on hand when calling.RIDGID¨ HAND HELD AND STAT

5This drill press has 12 speeds as listed below:300 RPM 1100 RPM400 RPM 1600 RPM450 RPM 1700 RPM600 RPM 1900 RPM650 RPM 2600 RPM700 RPM 3100 RPMSee in

6Safety Instructions For Drill Press (continued)- Use the spindle speed recom-mended for the specific operationand workpiece material - check theinsid

7Glossary of TermsWorkpieceThe item on which the cutting operation isbeing performed.Drill Bit or DrillThe cutting tool used in the drill press tomake

8Motor Specifications and Electrical Requirements(continued)110-120 Volt, 60 Hz. Tool InformationNOTE: The plug supplied on your toolmay not fit into

9Motor Safety ProtectionIMPORTANT: To avoid motor damage,this motor should be blown out or vacu-umed frequently to keep sawdust frominterfering with n